10BaseT - определение. Что такое 10BaseT
Diclib.com
Словарь ChatGPT
Введите слово или словосочетание на любом языке 👆
Язык:

Перевод и анализ слов искусственным интеллектом ChatGPT

На этой странице Вы можете получить подробный анализ слова или словосочетания, произведенный с помощью лучшей на сегодняшний день технологии искусственного интеллекта:

  • как употребляется слово
  • частота употребления
  • используется оно чаще в устной или письменной речи
  • варианты перевода слова
  • примеры употребления (несколько фраз с переводом)
  • этимология

Что (кто) такое 10BaseT - определение

ETHERNET PHYSICAL LAYERS USING TWISTED-PAIR CABLES
10baseT; 10BaseT; 10/100 Ethernet; 10/10BaseT; 10Base-T; 10BASET; Ethernet 10BaseT; UTP Ethernet; Unshielded Twisted Pair Ethernet; 10BT; 10/100 card; 10BASE-T; Twisted pair ethernet; Twisted-pair Ethernet; 10/100/1000; 10/100; 10/100/1000 Ethernet; 100MbE; 10MbE; MbE; 1MbE; 10 base t; 10baset; 802.3i; Twisted pair Ethernet; 10-BaseT; Ethernet over tp; Wired Ethernet; Base-T; Ethernet over twisted-pair; 10BASE-T1L; 10BASE-T1S
  • Cat 6A cable]] with an M12X connector in one end and a modular connector in the other
  • [[8P8C]] modular plug pin positioning
  • Pair 1 Wire 2
  • Pair 1 Wire 2
  • Pair 4 Wire 2
  • Pair 4 Wire 2
  • Pair 3 Wire 2
  • Pair 3 Wire 2
  • Pair 2 Wire 2
  • Pair 2 Wire 2
  • Pair 1 Wire 1
  • Pair 1 Wire 1
  • Pair 4 Wire 1
  • Pair 4 Wire 1
  • Pair 3 Wire 1
  • Pair 3 Wire 1
  • Pair 2 Wire 1
  • Pair 2 Wire 1

10baseT         
<networking> A variant of Ethernet which allows stations to be attached via twisted pair cable. (1995-01-24)
Ethernet over twisted pair         
Ethernet over twisted-pair technologies use twisted-pair cables for the physical layer of an Ethernet computer network. They are a subset of all Ethernet physical layers.

Википедия

Ethernet over twisted pair

Ethernet over twisted-pair technologies use twisted-pair cables for the physical layer of an Ethernet computer network. They are a subset of all Ethernet physical layers.

Early Ethernet used various grades of coaxial cable, but in 1984, StarLAN showed the potential of simple unshielded twisted pair. This led to the development of 10BASE-T and its successors 100BASE-TX, 1000BASE-T and 10GBASE-T, supporting speeds of 10 and 100 megabit per second, then 1 and 10 gigabit per second respectively.

Two new variants of 10 megabit per second Ethernet over a single twisted pair, known as 10BASE-T1S and 10BASE-T1L, were standardized in IEEE Std 802.3cg-2019. 10BASE-T1S has its origins in the automotive industry and may be useful in other short-distance applications where substantial electrical noise is present. 10BASE-T1L is a long-distance Ethernet, supporting connections up to 1 km in length. Both of these standards are finding applications implementing the Internet of things.

The earlier standards use 8P8C modular connectors, and supported cable standards range from Category 3 to Category 8. These cables typically have four pairs of wires for each connection, although early Ethernet used only two of the pairs. Unlike the earlier -T standards, the -T1 interfaces were designed to operate over a single pair of conductors and introduce the use of two new connectors referred to as IEC 63171-1 and IEC 63171-6.